Choose where your usage comes from. With Appliances, you add the appliances in your home (fans, ACs, fridge, lights, iron and so on) with their wattage, how many you have (for example 2 × ceiling fan) and the time window each one is usually on. The calculator works out each line's units (1 unit = 1 kWh) as watts × quantity × hours per day × 30 ÷ 1,000 and adds them up to get your monthly units. With Units, you type the units from your bill. With Bill amount, you type a bill total and the calculator works out the units that would produce it at your rate settings. The units are then priced in one of two ways:
Taxes and charges (optional): by default the result is the energy cost only, so your actual bill will normally be higher. Turn on Taxes & charges and type in the values from your own bill: fuel adjustment (FPA) in rupees per unit, fixed charges per month, electricity duty (%), GST (%, pre-filled at 18) and other fees such as the TV fee or meter rent. The estimate then shows a line-by-line bill. The taxes are worked out on simplified bases, so the total is approximate. It is a planning tool, not a copy of your DISCO bill.
Slab warning: when your units are close to the 200-unit protected line, or just past an un-protected slab line, the calculator shows how much the bill would change. If you built an appliance list, it also suggests a cut, such as running your AC some minutes less a day.
NEPRA determines electricity tariffs and the federal government notifies a uniform schedule that the distribution companies (DISCOs) apply. For homes with a sanctioned load below 5 kW, the residential (A-1) schedule splits consumers into protected and un-protected groups:
| Monthly units | Category | Variable rate (Rs/unit) |
|---|---|---|
| 1–100 | Protected | 10.54 |
| 101–200 | Protected | 13.01 |
| 1–100 | Un-protected | 22.44 |
| 101–200 | Un-protected | 28.91 |
| 201–300 | Un-protected | 33.10 |
| 301–400 | Un-protected | 36.46 |
| 401–500 | Un-protected | 38.95 |
| 501–600 | Un-protected | 40.22 |
| 601–700 | Un-protected | 41.85 |
| Above 700 | Un-protected | 47.20 |
Last checked: October 2026 · Source: IESCO tariff guide, A-1 residential, S.R.O. 279(I)/2026. Lifeline consumers (up to 100 units, separate rates) and homes with 5 kW or more sanctioned load (time-of-use tariff) are billed differently. These are base variable rates only; fixed charges per kW of sanctioned load, FCA, QTA and taxes are added on top. Read our full NEPRA tariff guide →
Use Slab tiers mode and pick Protected or Un-protected to match the category on your bill; the default rates are the ones in the table above. If you would rather work from your bill's bottom line, use Flat rate mode with your bill's total divided by the units billed. Your latest bill shows your units, your tariff category and the rate you were charged, which are the best numbers to start from.
A real bill adds a fixed charge based on your sanctioned load, the monthly fuel charges adjustment, the quarterly tariff adjustment, general sales tax (18%, as reported from FBR figures in June 2026), electricity duty, which varies by province, and the TV fee. None of these is added unless you turn on Taxes & charges and enter the amounts from your own bill; BillHisab does not fill in the fuel adjustment or other monthly charges for you. The quarterly tariff adjustment has no field of its own.
Want a quick figure without listing appliances? Our electricity bill by units table shows the energy cost of 100 to 1,000 units at protected and un-protected rates. Facing load shedding? The UPS backup time calculator estimates how long your inverter battery will last and what UPS size your load needs.
Thinking about rooftop panels? Use the Solar ROI calculator and read our guide to solar in Pakistan.
At 200 units or less (for six months running) you are a protected consumer with much lower rates and the benefit of one previous slab. Above 200 units you are billed as un-protected, where every unit is charged at the rate of the slab your total falls in, and you can stay un-protected for the next six months. That is why a few extra units can raise the bill far more than you would expect.
Only if you add them. By default it estimates the energy cost at the flat rate or slab rates you choose, so your actual bill will normally be higher. Turn on the optional Taxes & charges section and type in the fuel adjustment (FPA), fixed charges, electricity duty, GST (pre-filled at 18%) and other fees such as the TV fee from your own bill, and the estimate shows a line-by-line bill. The taxes use simplified bases, so the total is approximate.
No, there is no DISCO or city selector. You enter the rate yourself, so you can use the rates printed on your own bill whichever company supplies you.
Air conditioners are usually the biggest users, typically drawing around 1,000–2,000 watts while running, depending on size and whether they are inverter models. Electric water heaters, irons and room heaters also draw a lot of power while on, and refrigerators run around the clock, so even a modest wattage adds up over a month. Add each appliance to the calculator to see its share of your units.
It is designed for residential connections. Commercial and industrial tariffs have different rate structures, fixed and demand charges, so check your DISCO's tariff schedule for those connections.
Staying at or below 200 units every month keeps you on protected rates if you qualify, so small savings matter most near that line. The calculator warns you when you are close to it. Inverter ACs and refrigerators and LED lighting reduce units, and setting the AC to 24–26°C instead of 18–20°C cuts compressor running time. If your bill is high all year, compare the cost of rooftop solar with our Solar ROI calculator.
Yes. The Share button shares a short text summary of your estimate and a link to the calculator through your phone's share sheet, or copies it to your clipboard. Your appliance list is not included in the link and nothing is uploaded. Your list and settings are saved only in your browser on this device.